Master Plumber Practice Exam

c - Of the possible answers, only the licensed code officer is the one who is allowed to interpret the code. Whether a plumbing installation passes or fails an inspection is subject to a code officer's interpretation. You can appeal a decision that you feel is incorrect or questionable. Even as a master plumber your understanding of the intent of the code is not absolute. The plumbing inspector is the final word in the field when it comes to an interpretation of the code.

The main purpose of a plumbing code is to safeguard the health, safety, property and public welfare of a community. It becomes legally enforceable when it is adopted by a governing body with jurisdiction.

The provisions of a local plumbing code will not be deemed to supersede state or federal law unless they exceed the requirements of the state or federal law, making the local requirement more stringent. This occurs only if the state or federal authority permits preemption.

d - Water heaters require that you apply for and receive a plumbing permit prior to the replacement of an existing water heater. After the replacement work is completed you must arrange for a plumbing inspection of the work by a code enforcement officer. All other plumbing fixtures can be replaced in their exact locations without the need for a permit or inspection. Due to the risk that can arise from a faulty installation of a water heater it is the rare fixture that does require a permit and inspection for a simple replacement.

All new installations are required to comply with the plumbing code. Other elements that may be required to meet current code requirements can include renovations, the replacement of fixtures, additions to a plumbing system and extensive repairs to plumbing systems. At no time can work done to a plumbing system make it unsafe or be detrimental to the system.

Adding new plumbing fixtures can overload existing plumbing. You must compute the total fixture-unit ratings and the demand that it will put on existing plumbing piping. It is possible that an existing pipe might have to be removed and replaced with a larger pipe.

The minimum number of plumbing fixture required for a single-family home is five. This includes a toilet, a lavatory, a bathing unit, a kitchen sink and a washing machine connection. Additional fixtures can be added, such as dishwashers and hose bibs.

Twenty-five inches is the maximum distance allowed between the front edge of a lavatory and the faucet installed on it when the fixture is to be rated as an accessible fixture.

The discharge tubing that is connected to a relief valve that is servicing a water heater, boiler or an expansion tank for a boiler is not allowed to be trapped. Discharge piping from the relief valve is to extend downward to a point within six inches of a floor. Ideally, the drainage tubing should terminate above a floor drain, but this is not a requirement. The end of the tubing is not to be threaded.

Commercial dishwashing machines are allowed to use high-temperature hot water that would not be allowed for a residential use. It is common for these machines to use hot water that has a temperature in excess of 140 degrees F. 165 degrees F is what is needed to sanitize 99.9% of bacteria according to NSF 3. Due to the high temperature of hot water used with commercial equipment the discharge from the dishwasher must discharge through either an air gap or an air break. The discharge is to enter a standpipe made of approved materials for the high-temperature water.

Circuit vents are allowed to tie into stack vents, vent stacks and venting systems that extend to outside air. They may also extend to outside air independently.

Drainage fixture units are the primary key needed to size waste stack vents. Once you have this, you will have a chart to work with to convert your information into a minimum pipe diameter for the piping. You will need to determine the total discharge of fixture units into one branch interval. The total discharge into the pipe, measured in fixture units, is also needed. With this in hand and the proper sizing chart, you will be able to cross reference from the chart to determine the minimum diameter of the stack size.

There cannot be more than twenty feet between an access opening and a cleanout when the cleanout is installed below a finished floor. More than one access opening may have to be provided for access to cleanouts in large buildings.

The minimum depth of a liquid trap seal is two inches. This depth must be maintained. If the trap is not used often the trap seal may evaporate. If there is a risk of the trap drying out, a trap prime is to be installed. This is a device that detects a falling level of liquid in a trap and then introduces water into the trap if the trap seal is in risk of dropping below the required minimum.

Public lavatories that are required to deliver waster at a pressure of 60 psi are required to have a maximum flow rate and consumption of 0.5 gpm. This does not seem like much water. Water conservation has long been a concern and newer fixtures are designed to operate properly while using less water.